
How to Assess Insulation Continuity and Performance in Your Home
Insulation is sold by thickness and type, but in a finished home what matters just as much is whether it is continuous. A loft that is well insulated except for a strip along the eaves, or a cavity wall that was filled everywhere except under the windows, loses heat at every gap, and the rooms beside those gaps are the ones that feel cold.
Those gaps are hidden. They sit behind plaster, under boards and inside cavities, and a visual inspection cannot see them without opening up the building. Thermal imaging can, indirectly. Where insulation is missing, thin, slumped or displaced, more heat passes through that part of the wall or ceiling, so its inside surface runs cooler and its outside surface a little warmer than the insulated area around it. In the heating season, with a steady temperature difference across the building, those differences become a map of where the insulation is and where it is not. The map is only as good as the conditions it was made in and the analysis that reads it, which is why this post spends as long on the limits as on the patterns.
This post is for homeowners checking a recent cavity fill or loft top-up, buyers wanting to know what a house really has, and landlords and builders looking at retrofit work. It explains how insulation continuity is assessed, what the patterns look like in the loft, in cavity walls and at the awkward junctions in between, and what a survey can and cannot tell you. Thermography Services (UK) surveys, analyses and reports; the insulation work is for the installer or builder.
How to Check Insulation Continuity in a Home
Insulation only works where it is present, so the gaps matter more than thickness.

How Insulation Gaps Show Up
Continuity, not just thickness
A layer of insulation slows the heat leaving a home across its whole area. Where the layer is broken, the heat finds the break. A gap in an otherwise good layer lets heat through at that spot, and it often sits exactly where condensation and cold spots appear. Continuity is therefore the first question to ask of any insulated wall, roof or floor, and it is the question a thermal survey is best placed to answer.
How a gap shows on a thermal image
The camera measures surface temperature, not insulation. A gap shows because of what it does to the surface. From inside a heated room, the ceiling or wall over a gap is cooler than the insulated area beside it. From outside, the same area is a little warmer, because more heat is reaching it. The shape of the pattern then tells the analyst what kind of gap it is likely to be.
Three things have to be in place for the shape to mean anything: a temperature difference of at least 10 °C between inside and outside, held for 12 hours so the building has settled; no sun on the faces being imaged; and dry surfaces. Without them, the pattern can come from the weather rather than the insulation.
The loft
The loft is often the easiest place to read gaps. Imaged from the rooms below, a well insulated ceiling is even in tone. Missing insulation shows as a cooler patch with a hard edge, often a rectangle where a board was laid or an area was never covered. Insulation that stops short of the eaves leaves a cooler strip along the top of the outside walls. The loft hatch is a frequent small gap of its own.
On a bungalow in Surrey, surveyed before an architectural redesign, the imaging found discontinuity in the loft insulation that was consistent with heat loss through the ceilings below. The flat-roofed extension on the same house read more evenly than the pitched roof, which is the kind of comparison a survey of the whole house makes possible.
Cavity walls and cavity fill
A filled cavity should read as an even wall from outside, broken only by the expected bridges at lintels, floor edges and frames. Gaps in the fill read differently: irregular warmer patches outside, cooler patches inside, often below window sills, under the eaves, around a meter box or a pipe, or at the top of a wall where the fill did not reach or has settled over time. Partial-fill boards that have slumped or come away from the inner leaf can leave a warmer band at the top of the section they were meant to cover.
The distinction between a gap and a bridge matters here. A bridge follows the structure and repeats; a gap in fill has its own irregular outline. The analysis classifies each one separately, because the question for the installer is different.
Other places continuity breaks
- where an extension or a loft conversion meets the original insulation
- room-in-roof spaces, at the knee walls and the sloping ceilings
- around windows replaced after the walls were insulated
- dormers, bay windows and box rooms over porches or garages
- floors over unheated spaces
Wet insulation is a separate case. Insulation that has taken on water insulates less well and can show as a cooler, softer-edged area inside. A thermal image can indicate it; a moisture test by another trade confirms it.
What a survey can say, and what it cannot
A thermal survey can show where insulation continuity breaks on the surfaces imaged, how far each pattern extends, and what each is consistent with: missing, displaced, thin or wet insulation, a thermal bridge, or air leakage. It can compare one part of a house with another, and it can show whether a pattern has changed after work has been done, if the second survey is made under the same conditions.
It cannot measure a U-value, name the type or thickness of insulation, or see inside a wall. It is qualitative, and it says so. A pattern consistent with missing cavity fill is a strong pointer, not a certainty; confirmation comes from an inspection of the cavity or the loft by the installer, a surveyor or a builder. The survey does not give a verdict on Building Regulations compliance. Its results are valid for the conditions recorded on the night.
What you receive
Each pattern is located on the house, shown in its thermal image and the matching photograph, classified and given a severity, with the conditions recorded. Every report is written and certified by our Level 3 thermographer, so the findings carry an analysis you can hand to the person doing the work. For a full assessment of walls, roof and floors, an insulation performance survey covers the house inside and out.
BS EN ISO 6781-1:2023 and Insulation
Qualitative, Not U-values
BS EN ISO 6781-1:2023 is the current standard for detecting heat, air and moisture irregularities in buildings by infrared methods, and it replaced BS EN 13187:1999. Missing, thin, displaced or wet insulation is a heat irregularity in its terms: a place where the surface temperature departs from the insulated area around it. The standard’s general procedure is what makes that departure meaningful, with a steady temperature difference across the envelope, no solar loading on the imaged faces, reference temperatures recorded, and the conditions written into the report. The method is qualitative. It locates and describes irregularities; it does not measure thermal transmittance, so no U-value, heat loss rate or energy figure comes from the images. Our surveys are aligned with its general procedures, and a finding that matters is confirmed by an inspection of the cavity or the loft by others.

Find the Gaps First
Before you top up the loft, chase an installer about cavity fill or plan a retrofit, it helps to know where the insulation actually stops. Thermography Services (UK) images walls, ceilings and roofs inside and out under recorded conditions, and explains every break in continuity and what it is consistent with. Every report is written and certified by our Level 3 thermographer, ready to share with whoever does the work. Tell us about the house for a quotation.







